MMX Chassis narrow
Description
Awesomatix MMX narrow Chassis (also fits MMCX)
For summer-season we tried to make another innovative move in our successfull A800 MMX lineup, and we did it
By the reason our Carbon is much harder than every original material we were able to make the Chassis more narrow than all others, in fact 8mm total.
To optimize the effect of the narrow Chassis we removed the holes for the "old" short swingarms to make the rear end even smaller which delays the point where the chassis touches the ground while accelerating out of corners.
Another change is that we repositioned the battery 4,5 and the servo 2,5mm more forward to gain a smoother incorner-steering while getting a more stable rear end while accelerating.
Due to the narrow design we also slightly had to re-position the Swaybar holders without need to change anything at the swaybars itselve.
The motor-cutouts became slightly bigger for 2 reasons, 1st to get little more place to set the ESC wire under the Motor and 2nd to prevent the motor from touching the chassis.
Cutouts for Diff/Spool also got slightly modified to increase Flex-behaviour for the new narrow design.
To use our brand new Y-stiffener for front area we already made all needed holes into the Chassis, as well as the re-positioned hole for our floating receiver/fan mount.
As already known from all our chassis the cutouts for rubber-inserts under the battery keep state of the art for improved flex behaviour
All edges CNC milled (lower side) 0,3x45°
Thickness: 2,0/2,2/2,5mm
Surface:
Carbon: https://rc-carbonstore.com/index.php?k=3&lang=eng
Carbon Color: https://rc-carbonstore.com/index.php?k=16&lang=eng
3D Wave: https://rc-carbonstore.com/index.php?k=11&lang=eng
Alutex: https://rc-carbonstore.com/Carbon-Sheet-Plate-Alutex
Please Note:
Because of these many variations we produce by individual order / after payment
Production Time is 1-3 days, depends on order situation
For summer-season we tried to make another innovative move in our successfull A800 MMX lineup, and we did it
By the reason our Carbon is much harder than every original material we were able to make the Chassis more narrow than all others, in fact 8mm total.
To optimize the effect of the narrow Chassis we removed the holes for the "old" short swingarms to make the rear end even smaller which delays the point where the chassis touches the ground while accelerating out of corners.
Another change is that we repositioned the battery 4,5 and the servo 2,5mm more forward to gain a smoother incorner-steering while getting a more stable rear end while accelerating.
Due to the narrow design we also slightly had to re-position the Swaybar holders without need to change anything at the swaybars itselve.
The motor-cutouts became slightly bigger for 2 reasons, 1st to get little more place to set the ESC wire under the Motor and 2nd to prevent the motor from touching the chassis.
Cutouts for Diff/Spool also got slightly modified to increase Flex-behaviour for the new narrow design.
To use our brand new Y-stiffener for front area we already made all needed holes into the Chassis, as well as the re-positioned hole for our floating receiver/fan mount.
As already known from all our chassis the cutouts for rubber-inserts under the battery keep state of the art for improved flex behaviour
All edges CNC milled (lower side) 0,3x45°
Thickness: 2,0/2,2/2,5mm
Surface:
Carbon: https://rc-carbonstore.com/index.php?k=3&lang=eng
Carbon Color: https://rc-carbonstore.com/index.php?k=16&lang=eng
3D Wave: https://rc-carbonstore.com/index.php?k=11&lang=eng
Alutex: https://rc-carbonstore.com/Carbon-Sheet-Plate-Alutex
Please Note:
Because of these many variations we produce by individual order / after payment
Production Time is 1-3 days, depends on order situation